Application Tools : Limewash Brushes
What you need to know when selecting, using and caring for limewash paint brushes
Words
© Andreas Riedel
Published
2025.01
How to use and care for limewash paint brushes
This is the right guide for you if you want to
- use limewash brushes for the application of limewash paint
- know how to use natural fibre brushes correctly and take care of them
- how to take care of your brush so they will last for more than one project
Limewash Paint Brushes
What type of brushes are recommended?
For all exterior and interior limewashing we recommend using a natural fibre limewash brush. Their unique bristle structure retains the correct amount of paint and releases it evenly across the surface during painting.
Limewash Paint Brush 4 x 14cm
Limewash Paint Brush 3 x 10cm
Small Tapered Brush
What limewash brush should I use for samples or small projects?
For applying Bauwerk Colour Sample Pots or Bauwerk Garden Pot Paint these small brushes make the task super easy
Limewash Paint Brush 3 x 7cm
Useful hints when working with natural bristle brushes
Useful hints when working with natural bristle brushes
01 Assemble your limewash brush
- this clip allows you to hang your brush from the side of your bucket. The bucket clip can be left off if not required.
- unpack and check that all parts for your brush are there
- screw in the handle with the optional bucket clip as shown in the image
02 Before first use : How to break in a new natural bristle brush
New brushes made from natural bristle brushes tend to lose a few bristles during the first use. This is totally normal and does not mean your brush is faulty. We show you how professionals prepare their new brush before first use in the following video.
Breaking in a new natural bristle brush
Flick your brush a few times back and forth across the the fingers of your outstretched hand. Or use the same movement across a slightly rough surface or a table edge. You then pull up and remove hairs that are loose or stick up above the main body of bristles.
Breaking in a Limewash Paint Brush
03 Limewash Application by brush : How much paint should the brush hold?
- dip the brush only into the paint for 2 to 3 cm (about one inch)
- give it a quick flick with the wrist to shake off any excess paint
- your brush should not be dripping paint when you move to the wall
04 Limewash Brushes : How to correctly hold a limewash block brush
- hold the brush closer to the brush body as shown in the image for greater control
- move the brush at right angle across your surface - this will engage all bristle tips and not just those on the outer edge
- use loose, free strokes on smooth surfaces, do not apply too much pressure
- on rough surfaces you may want to use smaller, sometimes more circular movements
There is more than one way to apply limewash paint – we share here only what we found works best for most projects using a brush
05 Limewash Application : Cutting into corners using a limewash brush
- always work wet in wet - do not cut in all edges and then paint over partially dried sections
- using the limewash block brush, deposit a good portion of the paint at a place near where you want to cut in
- holding the brush close to the brush body angle slightly away from the corner to see the edge
- pull the brush along the corner using a little bit of pressure only
- brush away from the corner to avoid seeing only brush strokes parallel to the corner
Video Tutorial
Watch our short video Easy tips- Cutting In with Limewash Paint showing how to paint in corners
06 Brush Care : How to clean + wash your limewash brush
06 Brush Care : How to clean + wash your limewash brush
- fill an adequately sized bucket with clean water
- hold on to the handle of the brush and shake the brush out under water – this will take only a few seconds
- shake out brush in the sink
- run the tap and rinse the remaining paint out always in the same direction towards the bristle ends
- shake out again and bring back the damp bristles into shape with your hands
- allow the brush to dry either by hanging the brush or by placing the brush upright on a rag
Important
Do not store you brush in a bucket with water overnight. Following our Care Instructions will keep your brush in good condition.For prolonged brush life use Bauwerk Colour Brush Cleaner
07 Store your limewash brush to use for the next limewash paint project
- after washing out the limewash paint brush allow it to fully dry before storing it away
- use a small cotton rag and wrap the brush up, making sure the bristles can retain their shape.
- store in a dry place
08 Disposal of used up limewash brushes
Our limewash brushes are made with natural materials. They can be safely disposed of with normal household refuse.
More FAQs about Limewash Paint Brushes
©
The content of https://www.bauwerkcolour.com is protected by copyright. The reproduction of information or data, in particular the use of texts, parts of texts or images, either manually or with the aid of AI, requires the prior consent of Bauwerk Colour GmbH or Bauwerk Colour Australia Pty Ltd.